"One Point Cutting" not only reduces angular cross cutting operations to an unusual degree of mechanical simplicity, but eliminates some adjustment motions entirely, cuts down the time factor on othe radjustment motions, is more adaptable to short ut production methods, and in many other ways greatly increases total production per hour.

It is never necessary to raise or lower the saw blade for any angle of cross cut. once properly set it is always correctly positioned, even on compound miter cuts. Such adjustments elimniated entirely.

Massive iron components, accurately machine, insure lawsting alignment and close tolerance cutting. the vibration dampening effect of cast iron adds years to the lifetime of the machine, while providing the smoothness of operation and accuracy that you require for your most intricate work.

Gauges always remain fixed beacuse the saw blade enter the cut at the same point, it is never necessary to rearrange the material to be cut of change the stops or gauges when changing cross cut angles. "One point cutting" eliminates the necessity of adjusting work and gauges as usually reqired when saw blade cuts at different points according to degree of angle.

All vital moving parts are protected by hardened steel. The telescoping ram is special heat treated hardened steel. The housing is provided with hardened steel bearing ways. The 32 roller bearings are hardened steel to assure easy finger touch motion and absolute permanent accuracy. Breakdowns or or time out for replacing parts is elimnated because Uni-point is built to last a lifetime.

Again, "one point cutting" allows the saw blade to pass thru the guide fence at the same point always. Cutting thru the fence at different points according to angle soon mtilates the fence requiring constant replacements. Thus, with Uni-point the fence last for years.

Not only can the stops remain fixed when angle of cut is changed, but can remain fixed however many changes are made provided the length of material remains the same. In other words, gauges need only be changed when the entire job is changed.

With a telescoping ram, the entire upper assembly recedes at the completion of each cutting stroke, leaving table free and clear for measuring and other work. No long arm to work around.

All adjustments are made in front of the machine, above or below the table. No reaching over the table. Everything handy and simple to adjust.

Instantaneous locking action provided at all common positions, such as straight cross-cutting, 45 degrees bevel, 45 degrees miter right or left, 45 degrees compound miter and ripping.

Specifications
Motor HP: 5, 7-1/2, 10
Saw Diameter: 16"
Saw Hole: 1"
Dado* Largest width on standard mandrel: 1-9/16"
Dado* Largest width on 1-3/8" diameter mandrel extension: 3"
Maximum depth of cut(16" saw): 4-1/2"
Cross cut capacity-guide fence regular position: 17-1/2"
Cross cut capacity-guide fence rear position: 25"
ripping capacity-between saw and regular guide fence: 23-1/2"
Ripping capacity-with guide fence moved to rear: 31"
Maximum 45 degrees miter, guide fence
-regular postion: 4" x 12-1/2"
-moved to rear: 4" x 8-1/2"
Maximum compound 45 degrees miter: 3" x 12-1/2"
Motor raises, center of arbor to table top max. : 10"
Motor lowers, center of arbor to table top min. : 3-5/8"
Size of table: 25" x 48"
Height of table: 32"
Angle capacity:
-Saw tilts to left: 45 degrees
-Saw pivot to right: 70 degrees
-Saw pivot to left: 45 degrees
Floor space, overall: 48" x 60"
Roller tables, length from saw blade to each end (std): 10'
Roller tables, width overall: 17-1/2"
Approx. net weight: 800 lbs
Approx. shipipng weight: 1000 lbs
Approx. shipping weight (export): 1200 lbs
Cubic contents (export): 104 cu. ft.

Standard Equipment:
Regular machine complete with guard and kick back preventer, magnetic starter with 110 volt at push button and automatic electric brake

*Special Dado guard must be used
**Motors: Totally enclosed fan cooled, available in 5, 7-1/2, 10HP, 208 230/460, 575 Volt, three phase.