The spindles are machined from stressproof steel and are precision ground. The wide separation between the upper and lower sealed for life bearings procides extreme shaft rigidity when running large diameter cutterheads. The heavy yoke assembly with full length gibbed vee ways maintains deflection-free bearing and spindle alingments.

Base: Heavy quill-base castings with flanged floor base gives firm setting. Yoke ways are carefully machined to assure full yoke bearing.

Table: Heavy duty, well ribbed castings allow attachment of oversized jigs and fixtures. Top surface is accurately ground - allows stock and forms to slide easily. Has fitted table ring at the spindle.

Yokes: Gibbed yokes, carefully machined and fitted into base assures absolute vertical spindle position through any adjustment. Precision ball bearings are sealed for life - need no lubrication.

Spindles: Rugged 1" diameter by 5" long spindle is accurately machined and ground for high speed production. Optional spindle sizes available.

Drives: 3, 5, 7-1/2, 10 or 15 HP rear-mounted motors swing on hinges to allow easy access. Has 2-1/2" endless belt drive with screw adjustment for close belt tensioning. Shaper is equipped with magnetic starter and 110 volt push-button controls.

Specifications:
Diameter of Spindle(standard machine): 1"
Vertical adjustment of Spindle: 4-1/2"
Length of Spindle at Collar: 5"
Size of Table: 42" x 84"
Distance between Spindles: 42"
Height of Table Top: 34-1/2"
Spindle Speed: 8000 RPM
Spindle Rotation(front of machine)
-RH Spindle: counter clockwise
-LH Spindle: clockwise
Size of dust spouts: 4"
Horsepower: 3, 5, 7-1/2, 10, 15 TEFC
Size of Throat Hole (standard machine): 4-1/2"
Floor Space: 84"wide x 45"deep
Domestic Shipping Weight: 3100 lbs.
Export Shipping Weight: 3500 lbs.
Cubic measure export boxed: 128 cu. ft.
Voltages: 208, 230/460, 575, 3 phase, 60 hz
Each 4" dust spout requires approximately 400 CFM air flow for dust collection

Accessories
-K-50 Fences with hold down springs
-Micrometer adjust for K-50 fences
-3/4, 7/8, 1-1/8, 1-1/4, 1-3/8, 1-1/2 solid spindles
-6-1/2 spindle length 1, 1-1/8, 1-1/4, 1-3/8 and 1-1/2 solid spindle only
-8" spindle length 1-1/4, 1-3/8 and 1-1/2 solid spindle
-Opposite spindle rotation RH, CW, LH, CCW
-Reversing solid spindles with reversing switches
-Detachable non-reversing spindle screw-on type 3/4, 7/8, 1, 1-1/8, 1-1/4"
-Detachable reversing spindle taper type 3/4, 7/8, 1, 1-1/8"
-Detachable router top 1/2" hole
-Collet spindle (3/4" max. collet bore)
-6000 or 4000 RPM spindle speed
-NEMA 12 electrics with fused disconnect
-24-volt push-button
-Hand brake lieu of foot brake
-Switch to disconnect power upon actuation of brake
-Miter gauge and dovetail slot (table ends only)
-Single phase 3, 5, 7-1/2 HP, 220 volt
-Throat hole and plates available: 8", 6-1/2" and nested
-Modifications to customer's order