The spindles are machined from stressproof steel and are precision ground. The wide separation between the upper & lower sealed for life bearings provides extreme shaft rigidity when running large diameter cutterheads. The heavy yoke assembly with full length gibbed vee ways maintains deflection-free bearing and spindle alignments.

Base: Heavy quill-base castings with flanged floor base gives firm setting. Yoke ways are carefully machined to assure full yoke bearing.

Table: Heavy duty, well ribberd castings allow attachment of oversized jigs and fixtures. Top surface is accurately ground - allows stock and forms to slide easily. Has fitted table ring at the spindle.

Yokes: Gibbed yokes, carefully machined and fitted into base assures absolute vertical spindle position through any adjustment. Precision ball bearings are sealed for life - need no lubrication.

Spindles: Rugged 1" diameter by 5" long spindle is accurately machined and ground for high speed production. Optional spindle sizes available.

Drives: 3, 5, 7-1/2, 10 or 15 HP rear-mounted motors swing on hinges to allow easy access. Has 2-1/2" endless belt drive with screw adjustment for close belt tensioning. Shaper is equipped with magnetic starter and 110 volt push-button controls.

Specifications:
Diameter of Spindle(standard machine): 1"
Vertical adjustment of Spindle: 4-1/2"
Length of Spindle at Collar: 5"
Size of Table: 24" center machine.....30" x 60"
30" center machiner....30" x 66"
Distance Between Spindles: 24" Std. or 30"
Height of Table Top: 34-1/2"
Spindle Speed: 8000 RPM
Spindle Rotation(front of machine):
-RH Spindle: counter clockwise
-LH Spindle: clockwise
Size of dust spouts: 4"
Horsepower: 3, 5, 7-1/2, 10, 15 TEFC
Size of Throat Hole (standard machine): 4-1/2"
Floor Space: 24" center machine....44" x 60"
30" center machine....44" x 66"
Domestic Shipping Weight: 2000 lbs.
Export Shipping Weight: 2300 lbs.
Cubic measure export boxed: 96 cu. ft.
Voltages: 208, 230/460, 575, 3 phase, 60 hz
Each 4" dust spout requires approximately 400 CFM air flow for dust collection.

Accessories:
-K-50 fences with hold down springs
-Micrometer adjust for K-50 fences
-3/4, 7/8, 1-1/8, 1-1/4, 1-3/8, 1-1/2 solid spindles
-6-1/2" spindle length 1, 1-1/8, 1-1/4, 1-3/8 and 1-1/2 solid spindle only
-8" spindle length 1-1/4, 1-3/8 and 1-1/2 solid spindle
-Opposite spindle rotation RH-CW, LH-CCW
-Reversing solid spindles with reversing switches
-Detachable non-serving spindle screw-on type 3/4, 7/8, 1, 1-1/8, 1-1/4"
-Detachable reversing spindle taper type 3/4, 7/8, 1, 1-1/8"
-6" front and rear table extensions
-Detachable router top 1/2" hole
-Collet spindle (3/4" max. collet bore)
-6000 or 4000 RPM spindle speed
-NEMA 12 electrics with fused disconnect
-24-volt push-button
-Hand brake in lieu of foot brake
-Switch to disconnect power upon actuation of brake
-Miter gauge and dovetail slot (table ends only)
-Single phase 3, 5, 7-1/2 HP, 220 volt
-Thorat hole and plates available: 8", 6-1/2" and nested
-Modifications to customer's order